Showing posts with label Dodge. Show all posts
Showing posts with label Dodge. Show all posts

Sunday, November 3, 2019

2008 - 2010 Chrysler Town & Country / Dodge Grand Caravan 4.0L engine air filter change

The engine air filter is easily replaced on these minivan models. Although, if you proceed with a straight-forward process of unlatching the air filter housing on the front and attempting to use brute force to remove the filter, you may break parts.

The following process has more steps than this job requires on other vehicles, but it is really quite easy.

WARNING: Do not do this procedure with a hot engine.

WARNING: Do not do this procedure when it is cold outside (below 40). All the parts are plastic and may break. Unless it is absolutely necessary, wait until a warmer day.

Materials
New air filter if replacing

Tools
None

Time
10 - 15 minutes

Procedure

    4.0L engine  with cover
  • Remove the engine cover. This is not hard. There are four points connecting the cover to the engine. Lift up of the front half of the cover with hands on both sides. Repeat for the back half.
4.0L engine without cover
  • Remove the hose from the right air cleaner housing. It is difficult to pull it straight out. Do not use tools. Place your right hand on the hose and pivot forward and backward - similar to the motion of revving a motorcycle. It should turn a bit as you work it off the case.
Remove this hose by twisting forward and backward
  • On the air cleaner housing push in the two plastic retaining clips. The front should pop up.
Push clip away to release the front of are cleaner housing. Picture shows when step is complete.
  • Three plastic tabs on the cover hold the back part in position. Slide the cover toward you. The filter should be exposed.
  • Air filter needing replaced!
  • Pull out the air filter element and inspect.

  • Replace with the new air filter element if necessary.
  • Slide air cleaner cover tabs back into the rear of the bottom of the cover. The three tabs should be in their seats.
  • The front should now line up so you may push the top down. You should hear both plastic tabs snap into place.
  • Reattach the hose on top of the air cleaner housing. It should just push on.
  • Replace the engine cover. Align the plastic studs with the holes on the cover. Push down firmly above each one to make sure it secured.
    Underside of engine cover. Make sure to align these locations with studs on engine.

Note: Do not skip using the engine cover. It does help insulate the hood slightly to keep the paint from discoloring.

Sunday, July 12, 2015

2008 - 2010 Chrysler Town & Country / Dodge Grand Caravan 4.0L oil change

For those having the 4.0L engine in the Chrysler Town & Country or Dodge Grand Caravan it is difficult finding sources on the Internet regarding any engine-related procedure.  The oil change is quite easy on this vehicle.  I'm able to do this oil change without raising the van in a matter of approximately 30 minutes.


Chrysler 4.0L engine
Materials
5.5 quarts of 10W-30 motor oil
Oil filter (Purolater PL-12222 or equivalent)
Oil catch pan that holds at least 6 quarts
Funnel for adding oil
Rags.  Lots of rags!

Tools
13 mm socket
Socket wrench
Oil filter cap-style wrench

Procedure
Make sure the oil filter comes with a gasket!

  • Get your motor oil.  The warranty requires 10W-30 that meets Chrysler MS-6395.  This Chrysler spec will be posted on the back of the bottle.  Most oil brands meet this requirement.  A notable exception is Mobil oil.  I believe this is due to lack of acquiring the spec from Chrysler more than not being compliant.  If your engine is still on warranty, make sure you use the correct stuff.  This is not a high performance engine.  Conventional oil is good enough; the engine almost always outlasts the rest of the vehicle!
  • Get your oil filter.  I generally use Purolater PureOne filters.  Have a store associate look the the correct model.  Note: Make sure that there is a gasket on the filter!
  • Warm the engine.  Drive it a couple miles so the oil is nice and hot.
  • Park the van on a level surface.  Before shutting off the engine, turn the steering wheel all the way to the right to ease access to the oil drain bolt.
  • From the passenger side, lay on the ground in front of the tire.  Looking up you should see the oil pan.
View from passenger-side.

Oil drain bolt o left.  Oil filter on right.
  • Place oil catch pan under the bolt.
  • Loosen the oil drain plug by turning counter-clockwise using a 13-mm socket and wrench.  I generally grab my torque wrench simply because the added length increases the torque I can apply to the bolt.
  • Once its loose, slowly turn while keeping pressure on the bolt so the hot oil stays in the engine's oil pan.  When you can tell its ready to come out, quickly remove the bolt.  The oil will be hot!  Also, don't drop the bolt into the oil pan.  Its no fun fishing it out of hot motor oil.
  • Pop open the hood.  The hood release is on the dash near the driver's left knee.
  • Unscrew counter-clockwise the engine's oil cap.  It is easily identified with a picture of an oil can and 10W-30 printed on it.  Removing this cap will increase the speed at which the hot oil exits the engine.  Make sure oil is still draining into the catch pan and not overshooting it!
  • Wait until the oil merely drips out of the oil pan.
  • Move the oil catch pan so it can get oil from the drain bolt hole and the oil filter.
  • Put a cap-style oil filter onto your wrench.
Cap-style oil filter remover on wrench.
  • Place the cap onto the oil filter.  Turn counter-clockwise to remove.  When its fully removed, it will dump hot oil.  Make sure your catch pan is placed accordingly.
  • Make sure the old oil filter still has the gasket attached to it.  If its not there, it could be stuck to the engine.  Remove it!  If you don't, you will have a serious oil leak later!  I have changed oil for 25 years and this van was the first that ever had the gasket stick to it.  It was easily removed after I wasted about 4 quarts of oil.
  • Wait for all oil to drip from the engine. This will take approximately 20 minutes.
  • Screw the bolt back into the engine block by hand.  Use your socket and wrench to further tighen it.  Do not over-tighten!  Use a torque wrench to be sure.  Note: The oil bolt contains a gasket.  See the diagrams below:
Correct placement of gasket on oil bolt.
Incorrect placement of gasket on oil bolt.
This needs pushed down into the seat.
  • Using your finger, smear oil on the oil filter gasket.  This will ensure a good seal.
  • Put the oil filter onto the oil filter shaft as tight as you can using your hands.  You may use a torque wrench to make sure its on tight enough.  Generally, I just make it as tight by hand as possible.
  • Place a funnel into the oil filler location in the engine compartment.
  • Add 5.5 quarts of oil.
  • Put oil filler cap back in place.
  • Fire up the engine and make sure the oil pressure light goes out.  If it doesn't, shut off the engine immediately.  Something is wrong.  Consult a car guy!
  • If there are any leaks, tighten the bolt or filter.
  • This Chrysler engine is odd.  It takes mine an entire evening for all the oil to drain into the oil pan.  Do a precursory check now to make sure its within spec on the dipstick.  Add if necessary.  Check a second time in the morning!